| DC
Solutions, Inc. Gate Operators
Now a part of The Chamberlain Group, DC Solutions, Inc. is a full line manufacturer providing barrier, slide and commercial and residential swing gate operators. Our mission is to provide innovative products for the access control and gate operator industry. Our commitment to our customers is to produce a superior product, backed by high quality and superior reliability. Our customer support and satisfaction is unequaled in the industry and is of the highest priority. We take pride that our products are delivered on-time in order to meet industry needs. All DC Solutions gate operators are equipped with an inherent power loss fail safe design. In the interest of safety to our customers and compliance with the National Electrical Codes, all our gate operators bear the UL mark of safety.Chamberlain provides the broadest line of perimeter access control products for use in the residential, commercial and institutional markets. • DC Solutions • DC Solutions Mega Slide • DC Solutions Mega SlideX • DC Solutions Mega Swing • DC Solutions Mega Arm • DC Solutions Mega Arm Sprint • |
  |
||||
 |
|||||
Mega Arm Barrier Arms |
DC Solutions Mega Arm and Mega Arm Tower -
Residential DC Barrier Gate Operator Mega Arm Specifications Voltage: 120 or 220V AC, Solar panel Frequency: 50 or 60Hz Amp Draw: 2 Amperes Nominal Backup Power: Requires (2) 7 Amp Hour 12 Volt DC (Yuasa NP7-12 or Equivalent) Enclosure Chassis: 1/4" Heavy Duty Rust Proof T-6 Aluminum Construction Cover: Removable Heavy Duty Molded U.V. Stable Polyethylene (White Standard, Colors Optional) Meets UL-746C, 94-5VO Finish: Polyester Polyurethane Baked On Power Coat (White Standard) Weight: 105 lb (Without Arm) Barrier Arm ( sold separately) Operation: Breakaway Design - Reusable Arm Attaches With Nylon Nuts Lengths: 3" O.D. Round Extruded Aluminum 12', 15' Available With Or Without Yellow/Black Stripes (15' Requires Internal Counter Weight) 4" O.D. Soft Padded Arm - Yellow Padded Sleeve (Uses 2" O.D. Tube) 12', 14' (Both Require Adaptor Collars) Material: 3" O.D. Extruded Aluminum Finish: White Polyester Polyurethane Baked On Powder Coat Drive Assembly Motor: High Torque 1/3 HP 24 VDC Permanent Magnet (TENV) - With Permanently Sealed Bearings Transmission: 60:1 Heavy Duty Gear Reducer Arm Travel: 89 Degrees Approximately Raise/Lower: 2.5 Seconds Approximately Mechanism: Direct Drive - No Crank Arms Or Rubber Bumpers Electronic Controller Technology: Micro Controller Based (RISC) Surge Protection: All Inputs Protected By Ultra Fast Transorb Surge Arrestors Isolated Inputs: Opto Isolated - Open, Close, Free Exit, Safety, Shadow, Aux Open Has Memory/Non-Memory Outputs: K1 Relay (Option), 24 VDC Regulated Accessory Power (500MA) Terminals: One 12 Pin Removable, Three 4 Pin Removable Timers: Select On/Off With 1 - 33 Seconds Via DIP Switch Selection Position Sensing: Magnetic Hall Effect Sensors - No Mechanical Roller Switches Motor Drive Output: State Of The Art Mosfet Motor Drive Technology Compatibility(Accessories): All AVI, Laser Barcode Scanners, Radio Receivers, Card Readers, Ticket Machines, Loop Detectors, Push Buttons, Token Machines (Note: Up To .5 Amp (500MA) 24 VDC Backed Up Accessory Power Available to Power Above Devices.) Dip Selections (Switches): Aux Input Memory/Non Memory, Timer On/Off, Auto Raise Arm If Power Fails With 15 Sec Delay/Fail Secure - Right Hand Operation/Left Hand Operation, Relay Pulse On OLS/Relay On Except When On CLS Safety Approvals: U.L. LISTED (U.S.), C-U.L. LISTED (CANADA) Safety Standards: UL-325 (U.S.), CSA 22.2#247 (CANADA) |
||||
| |
|||||
|
|
|
|
||
