 
| |
|
|
|
|
|
Doorking Parking Controls |
 |
|
 |
1601 |
|
 |
1601
Manual
|
|
|
APPLICATIONS: The 1601 operator is designed
for single lane (14 ft. max) vehicular traffic control in high
traffic commercial and industrial applications. The 1601 operator
is designed so that it can be mounted on either the left or
right hand side of the roadway. The operator can be equipped
with a DC convenience open package (optional) that will automatically
raise the arm in the event of a power outage.
ADVANCED FEATURES: Magnetic limit control.
Ports for plug-in loop detectors. Automatic sequencing inputs
for use with slide and swing gate operators. Two convenience
outlets. 360° gear box rotation. Gate tracker reporting
output. Programming switches. Built-in power On/Off switch.
Left or right hand mount.
|
 |
OPTIONS AVAILABLE: Stainless
steel housing. DC powered convenience open. 14-foot wood arm.
Wood arm folding bracket for low headroom. 12-foot plastic arm.
Plastic arm folding bracket for low headroom. Plug-in loop detectors.
Heater kit for cold environments. Fan kit for hot humid environments.
|
|
SPECIFICATIONS Model 1601:
1/2 HP continuous-duty motor. 115 VAC. 230 VAC. 460 VAC. 40:1
gear-box running in a continuous oil bath. Arm rotates 90°
in approximately 1.5 seconds. Class II, III and IV applications.
Compliant with UL 325 and 991. ETL Listed. (Note: To be compliant
with UL 325 and industry safety guidelines, additional secondary
entrapment prevention devices may need to be installed with
this gate operator. Your professional DKS system installer can
provide you with more details on these devices and on current
industry safety standards.) Dimensions (operator only): 15"W
x 38"H* x 15"D.
|
|
1602 |
|
|
1602
Manual
|
|
|
APPLICATIONS: The 1602 operator is designed
for traffic lanes up to 20-feet wide in low use commercial and
industrial applications. This operator uses a counter-balanced
three-piece wishbone style arm assembly. The 1602 operator is
designed so that it can be mounted on either the left or right
hand side of the roadway. The operator can be equipped with
a DC convenience open package (optional) that will automatically
raise the arm in the event of a power outage.
ADVANCED FEATURES: Magnetic limit control.
Ports for plug-in loop detectors. Automatic sequencing inputs
for use with slide and swing gate operators. Two convenience
outlets. 360° gear box rotation. Gate tracker reporting
output. Programming switches. Built-in power On/Off switch.
Left or right hand mount.
|
|
OPTIONS AVAILABLE: Stainless
steel housing. DC powered convenience open. 20-foot three-piece
wood arm - counter balanced. Plug-in loop detectors. Heater
kit for cold environments. Fan kit for hot humid environments.
|
|
SPECIFICATIONS Model 1602:
1 HP continuous-duty motor. 115 VAC. 230 VAC. 460 VAC. 60:1
gear-box running in a continuous oil bath. Arm rotates 90°
in approximately 5.5 seconds. Class III and IV applications.
Compliant with UL 325 and 991. ETL Listed. (Note: To be compliant
with UL 325 and industry safety guidelines, additional secondary
entrapment prevention devices may need to be installed with
this gate opertator. Your professional DKS system installer
can provide you with more details on these devices and on current
industry safety standards.) Dimensions (operator only): 15"W
x 38"H* x 15"D. |
|
2000 |
|
|
2000
Manual
|
|
|
APPLICATIONS: The Model 2000 Power Inverter
is designed to provide backup power for a complete access control
system when primary (AC) power fails. The model 2000 is not
just another DC backup system. This unit converts DC battery
power to AC power to keep your system operable at all times.
The system acts as a power distribution panel during normal
(AC) operation, and supplies backup power to the load during
power outages. This capability ensures that the access control
system remains operable during power outages and is ideal for
any application where maintaining the access control system
is critical. These include high security needs, government and
military installations, apartment complexes and gated communities.
|
|
| SPECIFICATIONS: Modified sine
wave output. Maximum 5voltage regulation (2.5 typical). Frequency
regulation 60 Hz (within 4. 120 VAC output voltage. 3-stage
charging. Temperature compensation probe included. Charger to
inverter: 32-millisecond transfer time. Inverter to charger:
40-seconds. ETL Listed. |
|
ADVANCED FEATURES: Three-stage battery charging
maintains proper battery voltage without over charging the batteries.
RMS regulation ensures loads have the same amount of power as
battery voltage changes. Provides a modified sine-wave output
suitable for a variety of applications. Electronic control circuit
monitors battery voltage while system is in inverter mode and
commands up to six gate operators to open sequentially when
battery reaches critical levels.
OPTIONS AVAILABLE WITH THIS OPERATOR:
1500 Watt, 12.5 Amp maximum load.
2400 Watt, 20 Amp maximum load.
3600 Watt, 30 Amp maximum load. |
|
1615 |
|
|
1615
|
|
|
APPLICATIONS: The 1615 warning sign provides
a means to inform drivers that a one way lane condition exist
and that proceeding in the wrong direction will result in severe
tire damage. Ideal for parking garages, industrial locations,
toll booths, or in any traffic control application utilizing
traffic control spikes. Never use traffic control spikes in
any application without this warning sign.
|
|
ADVANCED FEATURES:
Light sensor for automatic operation. Built-in flood lamp for
spike illumination. Keyed on/off override switch.
|
|
SPECIFICATIONS Model 1615:
Illuminated with two 20-watt fluorescent lamps.
150-watt flood lamp for spike illumination.
115 VAC.
ETL LIsted.
Dimensions: 24"H x 24"W x 8"D.
Designed to be mounted on 3" mounting pipe (not included).
|
|
TRAFFIC SPIKES AND SPEED BUMPS |
|
|
|
|
|
APPLICATIONS: Traffic control products are
ideal for controlling traffic direction and speed through a
controlled entry location. Traffic spikes prevent vehicles from
proceeding through a traffic lane in the wrong direction by
enforcing one-way traffic lanes. Speed bumps force drivers to
slow down while driving through the controlled entry point.
They are also is ideal for keeping vehicular traffic at a safe
speed while driving over traffic spikes.
|
|
Warning signs (model 1615)
must be used with traffic spikes to warn drivers that a one-way
traffic lane condition exist. Speed bumps should always be used
with traffic spikes. Speeds in excess of 5-MPH over the spikes
can cause tire damage.
|
|
SPECIFICATIONS Traffic Spikes:
Individual spring loaded spikes. Stainless steel springs. Weight
spikes (no springs) version available. Flush in-ground unit.
Painted bright red for easy visibility. Ideal to enforce one-way
traffic. Dimensions: 6.5"H x 12.5"W x 72"L.
SPECIFICATIONS Speed Bumps:
Speed bumps are constructed from solid composite material. Speed
bumps can be easily removed and re-installed. Painted bright
yellow for easy visibility. Designed for installation on concrete
surfaces only. Dimensions: 2"H x 11.5"W x 72"L. |
|
|
|
|
