| MillerEdge MillerEdge, Inc. is the leading manufacturer of the most positive emergency stopping devices available for motor-driven doors and gates. It is our policy to supply quality products that conform exactly to all established requirements and the reasonable expectations of its customers. We are further committed to a company-wide program for continuous quality improvement. |
 |
||
 |
|||
 |
MGR20 |
||
|
|||
 |
MGO20 The MGO20 is designed for use on doors and gates up to 1-1/2 inches thick. To install, simply attach the rigid PVC or aluminum mounting channel and slide sensor into the channel. This edge cannot be bent or folded. When touched, these pressure sensitive edges immediately send an electrical signal to your controls to stop, and/or reverse operations. Designed for use in a wide variety of applications, these SensingEdges are extremely durable and can be used indoor or out. They are resistant to water, flame, and common greases and oils. • Manual • • Brochure • |
||
|
|||
 |
MGS20 Designed specifically for easy installation on standard 2” round or square frames, the MGR20 and MGS20 offer 3-sided activation for an added measure of protection. When touched, these electrically activated edge sensors immediately signal the gate operator to stop and/or reverse. The sleek design will not detract from the appearance of the gate. • Manual • • Brochure • |
||
|
|||
 |
MWT02 The Miller Edge Model MWT02 gate and door edge transmitter is designed to provide obstacle sensing protection for a variety of motorized gates and doors. It is easily mounted and wired to the gate or door edge sensor. When the SensingEdge comes into contact with an obstruction, a closed circuit signal is created and is sent to the transmitter. The transmitter relays the information to the receiver and the receiver passes the message along to the operator motor. The gate or door stops movement instantaneously and will then reverse the direction of travel. • Manual • • Brochure • |
||
|
|||
 |
MWTA02 he Miller Edge Model MWTA02 gate and door edge transmitter is designed to provide obstacle sensing protection for a variety of motorized gates and doors. It is easily mounted and wired to the gate or door edge sensor. When the SensingEdge comes into contact with an obstruction, a closed circuit signal is created and is sent to the transmitter. The transmitter relays the information to the receiver and the receiver passes the message along to the operator motor. The gate or door stops movement instantaneously and will then reverse the direction of travel. The Model MWTA02 is available with an Audible Alarm feature that activates when the battery has only 25% of its life remaining, indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals. • Manual • • Brochure • |
||
|
|||
 |
BEA Falcon The Falcon’s state-of-the-art microprocessor and flat antenna provide the ability to disregard pedestrians and only allow large masses (such as trucks and forklifts) to be detected-even at lower mounting heights. * Customizable: The Falcon allows for Uni or Bi-directional sensing, and the unique ability to open a door when traffic is moving away from the sensor. It may be set to discriminate between pedestrian and vehicular traffic. * Universally compatible with any industrial door. * Touch construction to handle the most extreme conditions. * Fast and Easy to set up and tune. * Saves energy and increases productivity • Manual • • Brochure • |
||
|
|||
 |
Matrix2-S Loop Detector
With more standard features than any other loop detector on the market, the Matrix2-S has the flexibility, compatibility and performance to maximize productivity and safety on your site Digital Inductive Single Loop Detector * Matrix 2-S is a series of digital inductive, single loop detectors for vehicle access control and safety doors, gates and numerous other applications. * The Matrix 2-S is available in two models to accommodate nearly any application. * Unlike traditional DIP switches, the Matrix 2-S’s continuous mode adjustments allow for precise settings to match your application. • Manual • • Brochure • |
||
|
|||
 |
MWCK02 The Miller Edge Model MWCK02 gate and door edge transmitter and receiver kit, is designed to provide a fully reliable, self checking communication between the 4-wire SensingEdge and the door or gate motor operator. • Manual • • Brochure • |
||
|
|||
 |
MWR03 The Miller Edge Model MWR03, 3-channel receiver is designed to work with most gate and commercial door operators. The one receiver is capable of receiving signals from up to 3 different input devices. • Manual • • Brochure • |
||
|
|||
 |
MWR02 Both the Miller Edge receiver and transmitters are designed to have several selectable options not found on other radio controls. Simply select these options with the convenient dip switches and wire harness. The receiver will operate on either 12 or 24 volt AC or DC and is capable of sending a pulse or continuous signal. • Manual • • Brochure • |
||
|
|||
