BD LOOPS SHIELD GREY
Item No. BD BD-LS-GREY
Loading
BD Loops Shield is a tough, long-lasting, flexible one-part moisture curing self-leveling hybrid sealant. BD-LS protects and shields inductance loop wire in concrete, asphalt, and other substrates. BD Loop Shield “BD-LS” is made using one of the most advanced, high performance polymer technologies a
Description
BD Loops Shield is a tough, long-lasting, flexible one-part moisture curing self-leveling hybrid sealant. BD-LS protects and shields inductance loop wire in concrete, asphalt, and other substrates. BD Loop Shield “BD-LS” is made using one of the most advanced, high performance polymer technologies available in sealants today.
USES
BD-LS is designed to seal inductance loops installed in saw-cut slots. BD-LS exhibits excellent adhesion to concrete, asphalt, paver stones, brick, and a variety of other substrates.
SUPERIOR FEATURES
· Self leveling.
· 100% Solids, will not shrink. No solvents.
· UV and weathering resistant.
· Does not bubble when exposed to water.
· Can be applied to damp/wet surfaces.
· Flat Sealant tip included with each tube of sealant. Seal the groove in 1 pass from the bottom up!
· 30 fl oz. rigid plastic tube.
· V.O.C. and California Prop 65 compliant.
· Paintable.
· Resists yellowing.
· Available in Gray or Black.
· Made in the USA.
Carefully cut the tip off the cartridge just above the nozzle threads. Thread sealant tip onto cartridge and place into quart sized caulking gun. Sealant should be applied from the bottom of the saw-cut groove. Slightly under fill the groove to be within 1/8” (3.12 mm) of the surface to prevent vehicles from tracking sealant. For easier application, pneumatic and battery powered dispensing guns are available. Do not use high speed setting on powered dispensing guns.
CURING
BD-LS will skin over in approximately 45 minutes at 70° F (21° C) and 50% relative humidity. Temperatures below 32°F (0°C) and/or low humidity will slow skin/cure time. Strength will start to develop immediately and continue increasing for 7 days after application. However, if the groove is slightly under-filled, traffic is permitted immediately after application. Not designed for installation in freezing temperatures. Use BD-LG2 for cold weather installations.
USES
BD-LS is designed to seal inductance loops installed in saw-cut slots. BD-LS exhibits excellent adhesion to concrete, asphalt, paver stones, brick, and a variety of other substrates.
SUPERIOR FEATURES
· Self leveling.
· 100% Solids, will not shrink. No solvents.
· UV and weathering resistant.
· Does not bubble when exposed to water.
· Can be applied to damp/wet surfaces.
· Flat Sealant tip included with each tube of sealant. Seal the groove in 1 pass from the bottom up!
· 30 fl oz. rigid plastic tube.
· V.O.C. and California Prop 65 compliant.
· Paintable.
· Resists yellowing.
· Available in Gray or Black.
· Made in the USA.
COVERAGE CHARTS
3/16″ Wide Blade/Groove
(Recommended Cut Width)
Cut Depth Coverage Per Tube Coverage Per Case
1 ¼” 20′ 240′
1 ½” 16′ 192′
¼” Wide Blade/Groove
Cut Depth Coverage Per Tube Coverage Per Case
1 ¼” 15′ 180′
1 ½” 12′ 144′
APPLICATIONCarefully cut the tip off the cartridge just above the nozzle threads. Thread sealant tip onto cartridge and place into quart sized caulking gun. Sealant should be applied from the bottom of the saw-cut groove. Slightly under fill the groove to be within 1/8” (3.12 mm) of the surface to prevent vehicles from tracking sealant. For easier application, pneumatic and battery powered dispensing guns are available. Do not use high speed setting on powered dispensing guns.
CURING
BD-LS will skin over in approximately 45 minutes at 70° F (21° C) and 50% relative humidity. Temperatures below 32°F (0°C) and/or low humidity will slow skin/cure time. Strength will start to develop immediately and continue increasing for 7 days after application. However, if the groove is slightly under-filled, traffic is permitted immediately after application. Not designed for installation in freezing temperatures. Use BD-LG2 for cold weather installations.
Specifications
- Vendor Item No.
- BD-LS GRY
- Item Category Code
- LOOP
Loading
BD LOOPS SHIELD GREY
Item No. BD BD-LS-GREY
BD Loops Shield is a tough, long-lasting, flexible one-part moisture curing self-leveling hybrid sealant. BD-LS protects and shields inductance loop wire in concrete, asphalt, and other substrates. BD Loop Shield “BD-LS” is made using one of the most advanced, high performance polymer technologies a
Description
BD Loops Shield is a tough, long-lasting, flexible one-part moisture curing self-leveling hybrid sealant. BD-LS protects and shields inductance loop wire in concrete, asphalt, and other substrates. BD Loop Shield “BD-LS” is made using one of the most advanced, high performance polymer technologies available in sealants today.
USES
BD-LS is designed to seal inductance loops installed in saw-cut slots. BD-LS exhibits excellent adhesion to concrete, asphalt, paver stones, brick, and a variety of other substrates.
SUPERIOR FEATURES
· Self leveling.
· 100% Solids, will not shrink. No solvents.
· UV and weathering resistant.
· Does not bubble when exposed to water.
· Can be applied to damp/wet surfaces.
· Flat Sealant tip included with each tube of sealant. Seal the groove in 1 pass from the bottom up!
· 30 fl oz. rigid plastic tube.
· V.O.C. and California Prop 65 compliant.
· Paintable.
· Resists yellowing.
· Available in Gray or Black.
· Made in the USA.
Carefully cut the tip off the cartridge just above the nozzle threads. Thread sealant tip onto cartridge and place into quart sized caulking gun. Sealant should be applied from the bottom of the saw-cut groove. Slightly under fill the groove to be within 1/8” (3.12 mm) of the surface to prevent vehicles from tracking sealant. For easier application, pneumatic and battery powered dispensing guns are available. Do not use high speed setting on powered dispensing guns.
CURING
BD-LS will skin over in approximately 45 minutes at 70° F (21° C) and 50% relative humidity. Temperatures below 32°F (0°C) and/or low humidity will slow skin/cure time. Strength will start to develop immediately and continue increasing for 7 days after application. However, if the groove is slightly under-filled, traffic is permitted immediately after application. Not designed for installation in freezing temperatures. Use BD-LG2 for cold weather installations.
USES
BD-LS is designed to seal inductance loops installed in saw-cut slots. BD-LS exhibits excellent adhesion to concrete, asphalt, paver stones, brick, and a variety of other substrates.
SUPERIOR FEATURES
· Self leveling.
· 100% Solids, will not shrink. No solvents.
· UV and weathering resistant.
· Does not bubble when exposed to water.
· Can be applied to damp/wet surfaces.
· Flat Sealant tip included with each tube of sealant. Seal the groove in 1 pass from the bottom up!
· 30 fl oz. rigid plastic tube.
· V.O.C. and California Prop 65 compliant.
· Paintable.
· Resists yellowing.
· Available in Gray or Black.
· Made in the USA.
COVERAGE CHARTS
3/16″ Wide Blade/Groove
(Recommended Cut Width)
Cut Depth Coverage Per Tube Coverage Per Case
1 ¼” 20′ 240′
1 ½” 16′ 192′
¼” Wide Blade/Groove
Cut Depth Coverage Per Tube Coverage Per Case
1 ¼” 15′ 180′
1 ½” 12′ 144′
APPLICATIONCarefully cut the tip off the cartridge just above the nozzle threads. Thread sealant tip onto cartridge and place into quart sized caulking gun. Sealant should be applied from the bottom of the saw-cut groove. Slightly under fill the groove to be within 1/8” (3.12 mm) of the surface to prevent vehicles from tracking sealant. For easier application, pneumatic and battery powered dispensing guns are available. Do not use high speed setting on powered dispensing guns.
CURING
BD-LS will skin over in approximately 45 minutes at 70° F (21° C) and 50% relative humidity. Temperatures below 32°F (0°C) and/or low humidity will slow skin/cure time. Strength will start to develop immediately and continue increasing for 7 days after application. However, if the groove is slightly under-filled, traffic is permitted immediately after application. Not designed for installation in freezing temperatures. Use BD-LG2 for cold weather installations.
Specifications
- Vendor Item No.
- BD-LS GRY
- Item Category Code
- LOOP