Mega Arm Sprint and Mega Arm Sprint Tower

DC Solutions Mega Arm Sprint and Mega Arm Sprint Tower DC Barrier Gate Operator
The Mega Arm Sprint and Mega Arm Sprint Tower are DC-powered, high-speed additions to the DC Solutions® family of gate operators. Designed with a 24V DC (1/2 HP equivalent) motor, these models provide exceptional speed, making them ideal for parking applications. Constructed with an aluminum alloy chassis, they´re corrosion resistant and light enough for one person to carry and install. The heavy-duty motor supports 10,000 cycles per day with an operator speed of .9 seconds to open or close.
The DC Solutions Mega Arm Sprint and Mega Arm Sprint Tower was made to be unique in the industry through innovative design and solid engineering. Its single State of the Art universal electronics control board eliminates the need for mechanical limit switches, relays and contactors. Arm position is limited by a magnet mounted on the drive shaft which is sensed by two magnetic sensors on the electronics controller. Its full service controller is capable of accepting inputs from telephone entry, loop detectors, card readers, push buttons, barcode scanners, and is equipped with multiple vehicle memory buffer. Built in regulated 24VDC backed up power provided for accessories (detectors, receivers, card readers). The standard break away arm design can allow the arm to be reused many times. Finally, its modern design and cutting edge technology will make the MEGA SPRINT the perfect choice for all your parking control applications.
No power? No problem!
Built-in battery backup provides seamless operation of the gate operator and all DC control and sensing devices in the event of a power loss.

Mega Arm Sprint Specifications
Voltage: 120 or 220V AC, Solar panel
Frequency: 50 or 60Hz
Amp Draw: 2 Amperes Nominal
Backup Power: Requires (2) 7 Amp Hour 12 Volt DC (Yuasa NP7-12 or Equivalent)
Chassis: 1/4″ Heavy Duty Rust Proof T-6 Aluminum Construction
Cover: Removable Heavy Duty Molded U.V. Stable Polyethylene (White Standard, Colors Optional) Meets UL-746C, 94-5VO
Finish: Polyester Polyurethane Baked On Power Coat (White Standard)
Weight: 105 lb (Without Arm)
Barrier Arm (not included, sold separately) Operation: Breakaway Design – Reusable Arm Attaches With Nylon Nuts
Lengths: 9′ x 4″ O.D. Soft Padded Arm – Yellow Padded Sleeve (Uses 2″ O.D. Tube) (Require Adaptor Collars)
Material: 2″ O.D. Extruded Aluminum with 4″ O.D. Soft Yellow Pad.
Motor: High Torque 1/3 HP 24 VDC Permanent Magnet (TENV) – With Permanently Sealed Bearings
Transmission: 60:1 Heavy Duty Gear Reducer
Arm Travel: 89 Degrees Approximately
Raise/Lower: 0.9 to 1 Second
Mechanism: Direct Drive – No Crank Arms Or Rubber Bumpers
Electronic Controller Technology: Micro Controller Based (RISC)
Surge Protection: All Inputs Protected By Ultra Fast Transorb Surge Arrestors Isolated Inputs: Opto Isolated – Open, Close, Free Exit, Safety, Shadow, Aux Open Has Memory/Non-Memory
Outputs: K1 Relay (Option), 24 VDC Regulated Accessory Power (500MA)
Terminals: One 12 Pin Removable, Three 4 Pin Removable
Timers: Select On/Off With 1 – 33 Seconds Via DIP Switch Selection
Position Sensing: Magnetic Hall Effect Sensors – No Mechanical Roller Switches
Motor Drive Output: State Of The Art Mosfet Motor Drive Technology
Compatibility(Accessories): All AVI, Laser Barcode Scanners, Radio Receivers, Card Readers, Ticket Machines, Loop Detectors, Push Buttons, Token Machines. Note: Up To .5 Amp (500MA) 24 VDC Backed Up Accessory Power Available to Power Above Devices.
Dip Selections (Switches): Aux Input Memory/Non Memory, Timer On/Off, Auto Raise Arm If Power Fails With 15 Sec Delay/Fail Secure – Right Hand Operation/Left Hand Operation, Relay Pulse On OLS/Relay On Except When On CLS, tail gate and tamper.
Options Relay: K1 Relay With Programmable Operation (Tailgate and tampers alarm latch, INTERLOCK, arm position, trap pulse and isolation)
Heater: 150 Watt Heater With Automatic Thermostat (For Use In Areas Where Temperatures Fall Below 15° F)
Slip Clutch : Allows arm to be forced up without causing damage – Arm lowers and self Aligns after car passes or set to close by timer. Arm will automatically re-level itself.
Cabinet: Full length rust proof aluminum tower

Standard Features
Fast access – very quick 1 second open/close time.
Built in battery backup – inherent 24 VDC backup power with regulated 24VDC for accessories.
High torque 24 volt Permanent Magnet DC motor.
Full service controller with eight inputs and LED indicators for loops, card reader, radio, etc…
Continuous duty operation toll rated at 10,000 cycles per day for all applications (even during power failures).
Reversible arm direction for right or left handed operation.
Instant Reverse Device (IRD) monitor senses obstructions going open and close.
Automatic open of gate arm when power is lost if desired (With 15 sec. delay selection).
Raise gate input memory will memorize multiple vehicles-ideal for barcode scanners & AVI.
Ability to have arm STOP in close travel if tailgating is sensed at close loop.
Break away mounting design for the 4″ x 9 Ft. soft padded aluminum safety arm (yellow).
All rust proof aluminum construction with powder coat baked on enamel.
Molded Polyethylene UV stabilized cover never needs wax or paint (white or colors).
Direct drive gear reducer eliminates many parts that might otherwise fail.
Microprocessor (RISC) based electronics with watch dog reset timer.
State of the art MOSFET motor drive technology, NO contactors or relays.
Dynamic motor braking to preserve arm positioning.
Soft start and stop in open and close travel motions.
No limit switches to fail-uses magnetic (Hall Effect) sensors to monitor arm position.
Maximum Run Timer for motor (MRT) with anti-tamper protection in closing direction.
Each unit configurable as master or slave operator.
Safe 24 VDC low voltage motor and control wiring.
Open architecture PCB with space for OVERDRIVE CPU for future expanded options.
LED diagnostic center for easy on-site trouble shooting.
Closing timer adjustable from 1-33 seconds with on / off selection.
Transorb diodes on all inputs for protection against transient voltage spikes.
Capable of being powered by 120 VAC, 220 VAC or Solar power, standard.
5 year perforation warranty on cover and chassis with 1 year on electronics and mechanism.
Interlock with memory when connected to a slide/swing gate operator, barrier will wait to raise until that unit reaches its full open position. Barrier will not raise if slide/swing gate is tampered with.
Tail gate alarm-K1 relay can be programmed to fire when a tail gater is sensed on the close loop.